|
|
Line 113: |
Line 113: |
| </math> | | </math> |
| | | |
− | ===Check=== | + | ===Total magnitude=== |
| + | Note that this provides a simple expression for ''q'' total: |
| + | :<math> |
| + | \begin{alignat}{2} |
| + | q & = \sqrt{ q_x^2 + q_y^2 + q_z^2 } \\ |
| + | & = \frac{2 \pi}{\lambda} \sqrt{ \sin^2 \theta_f \cos^2 \alpha_f + \left ( \cos \theta_f \cos \alpha_f - 1 \right )^2 + \sin^2 \alpha_f } \\ |
| + | \left( \frac{q}{k} \right)^2 |
| + | & = \sin^2 \theta_f \cos^2 \alpha_f + \cos^2 \theta_f \cos^2 \alpha_f -2 \cos \theta_f \cos \alpha_f + 1 + \sin^2 \alpha_f \\ |
| + | & = \cos^2 \alpha_f (\sin^2 \theta_f + \cos^2 \theta_f) +\sin^2 \alpha_f -2 \cos \theta_f \cos \alpha_f + 1 \\ |
| + | & = \cos^2 \alpha_f (1) +\sin^2 \alpha_f -2 \cos \theta_f \cos \alpha_f + 1 \\ |
| + | & = 2 -2 \cos \theta_f \cos \alpha_f \\ |
| + | q & = \sqrt{2}k \sqrt{ 1 - \cos \theta_f \cos \alpha_f } \\ |
| + | \end{alignat} |
| + | </math> |
| + | |
| + | ====Check==== |
| As a check of these results, consider: | | As a check of these results, consider: |
| :<math> | | :<math> |
Line 127: |
Line 142: |
| </math> | | </math> |
| And: | | And: |
− | :<math>
| |
− | \begin{alignat}{2}
| |
− | q & = \sqrt{ q_x^2 + q_y^2 + q_z^2 } \\
| |
− | & = \frac{2 \pi}{\lambda} \sqrt{ \sin^2 \theta_f \cos^2 \alpha_f + \left ( \cos \theta_f \cos \alpha_f - 1 \right )^2 + \sin^2 \alpha_f } \\
| |
− | \left( \frac{q}{k} \right)^2
| |
− | & = \sin^2 \theta_f \cos^2 \alpha_f + \cos^2 \theta_f \cos^2 \alpha_f -2 \cos \theta_f \cos \alpha_f + 1 + \sin^2 \alpha_f \\
| |
− | \end{alignat}
| |
− | </math>
| |
| | | |
| ===Check 2=== | | ===Check 2=== |
Revision as of 11:36, 30 December 2015
In transmission-SAXS (TSAXS), the x-ray beam hits the sample at normal incidence, and passes directly through without refraction. TSAXS is normally considered in terms of the one-dimensional momentum transfer (q); however the full 3D form of the q-vector is necessary when considering scattering from anisotropic materials. The q-vector in fact has three components:
This vector is always on the surface of the Ewald sphere. Consider that the x-ray beam points along +y, so that on the detector, the horizontal is x, and the vertical is z. We assume that the x-ray beam hits the flat 2D area detector at 90° at detector (pixel) position . The scattering angles are then:
where is the sample-detector distance, is the out-of-plane component (angle w.r.t. to y-axis, rotation about x-axis), and is the in-plane component (rotation about z-axis). The alternate angle, , is the elevation angle in the plane defined by .
Total scattering
The full scattering angle is defined by a right-triangle with base d and height :
The total momentum transfer is:
Given that:
We can also write:
Where we take for granted that q must be positive.
In-plane only
If (and ), then , , and:
The other component can be thought of in terms of the sides of a right-triangle with angle :
Summarizing:
Out-of-plane only
If , then , , and:
The components are:
Summarizing:
Components
The momentum transfer components are:
In vector form:
Total magnitude
Note that this provides a simple expression for q total:
Check
As a check of these results, consider:
And:
Check 2
As a check of these results, consider:
Where we used:
And, we further note that:
cont
Continuing: